Coal is a combustible black or brownish-black sedimentary rock, formed as rock strata called coal seams. Coal is mostly carbon with variable amounts of other elements; chiefly hydrogen, sulfur, oxygen, and nitrogen. Coal is formed when dead plant matter decays into peat and is converted into coal by the heat and pressure of deep burial over millions of years. Vast deposits of coal originates in former wetlands—called coal forests—that covered much of the Earth's tropical land areas during the late Carboniferous (Pennsylvanian) and Permian times.
As a fossil fuel burned for heat, coal supplies about a quarter of the world's primary energy and two-fifths of its electricity. Some iron and steel making and other industrial processes burn coal.
The extraction and use of coal causes many premature deaths and much illness. Coal industry damages the environment, including by climate change as it is the largest anthropogenic source of carbon dioxide, 14 Gt in 2016, which is 40% of the total fossil fuel emissions. As part of the worldwide energy transition many countries have stopped using or use less coal, and the UN Secretary General has asked governments to stop building new coal plants by 2020.
The largest consumer and importer of coal is China. China mines almost half the world's coal, followed by India with about a tenth. Australia accounts for about a third of world coal exports followed by Indonesia and Russia.
The word originally took the form col in Old English, from Proto-Germanic *kula(n), which in turn is hypothesized to come from the Proto-Indo-European root *g(e)u-lo- "live coal". Germanic cognates include the Old Frisian kole, Middle Dutch cole, Dutch kool, Old High German chol, German Kohle and Old Norse kol, and the Irish word gual is also a cognate via the Indo-European root.
One theory states that about 360 million years ago, some plants evolved the ability to produce lignin, a complex polymer that made their cellulose stems much harder and more woody. Thus, the first trees evolved. But bacteria and fungus did not immediately evolve the ability to decompose lignin, so the wood did not fully decay but became buried under sediment, eventually turning into coal. About 300 million years ago, mushrooms and other fungi developed this ability, ending the main coal-formation period of earth's history.
At various times in the geologic past, the Earth had dense forests in low-lying wetland areas. Due to natural processes such as flooding, these forests were buried underneath soil. As more and more soil deposited over them, they were compressed. The temperature also rose as they sank deeper and deeper. As the process continued the plant matter was protected from biodegradation and oxidation, usually by mud or acidic water. This trapped the carbon in immense peat bogs that were eventually covered and deeply buried by sediments. Under high pressure and high temperature, dead vegetation was slowly converted to coal. The conversion of dead vegetation into coal is called coalification. Coalification starts with dead plant matter decaying into peat. Then over millions of years the heat and pressure of deep burial causes the loss of water, methane and carbon dioxide and an increase in the proportion of carbon. Thus first lignite (also called "brown coal"), then sub-bituminous coal, bituminous coal, and lastly anthracite (also called "hard coal" or "black coal") may be formed.
The wide, shallow seas of the Carboniferous Period provided ideal conditions for coal formation, although coal is known from most geological periods. The exception is the coal gap in the Permian–Triassic extinction event, where coal is rare. Coal is known from Precambrian strata, which predate land plants—this coal is presumed to have originated from residues of algae.
Sometimes coal seams (also known as coal beds) are interbedded with other sediments in a cyclothem.
There are several international standards for coal. The classification of coal is generally based on the content of volatiles. However the most important distinction is between thermal coal (also known as steam coal), which is burnt to generate electricity via steam; and metallurgical coal (also known as coking coal), which is burnt at high temperature to make steel.
Hilt's law is a geological observation that (within a small area) the deeper the coal is found, the higher its rank (or grade). It applies if the thermal gradient is entirely vertical; however, metamorphism may cause lateral changes of rank, irrespective of depth.
The earliest recognized use is from the Shenyang area of China where by 4000 BC Neolithic inhabitants had begun carving ornaments from black lignite. Coal from the Fushun mine in northeastern China was used to smelt copper as early as 1000 BC. Marco Polo, the Italian who traveled to China in the 13th century, described coal as "black stones ... which burn like logs", and said coal was so plentiful, people could take three hot baths a week. In Europe, the earliest reference to the use of coal as fuel is from the geological treatise On stones (Lap. 16) by the Greek scientist Theophrastus (c. 371–287 BC):
Among the materials that are dug because they are useful, those known as anthrakes [coals] are made of earth, and, once set on fire, they burn like charcoal. They are found in Liguria ... and in Elis as one approaches Olympia by the mountain road; and they are used by those who work in metals.
Outcrop coal was used in Britain during the Bronze Age (3000–2000 BC), where it formed part of funeral pyres. In Roman Britain, with the exception of two modern fields, "the Romans were exploiting coals in all the major coalfields in England and Wales by the end of the second century AD". Evidence of trade in coal, dated to about AD 200, has been found at the Roman settlement at Heronbridge, near Chester; and in the Fenlands of East Anglia, where coal from the Midlands was transported via the Car Dyke for use in drying grain. Coal cinders have been found in the hearths of villas and Roman forts, particularly in Northumberland, dated to around AD 400. In the west of England, contemporary writers described the wonder of a permanent brazier of coal on the altar of Minerva at Aquae Sulis (modern day Bath), although in fact easily accessible surface coal from what became the Somerset coalfield was in common use in quite lowly dwellings locally. Evidence of coal's use for iron-working in the city during the Roman period has been found. In Eschweiler, Rhineland, deposits of bituminous coal were used by the Romans for the smelting of iron ore.
No evidence exists of the product being of great importance in Britain before about AD 1000, the High Middle Ages. Mineral[clarification needed] coal came to be referred to as "seacoal" in the 13th century; the wharf where the material arrived in London was known as Seacoal Lane, so identified in a charter of King Henry III granted in 1253. Initially, the name was given because much coal was found on the shore, having fallen from the exposed coal seams on cliffs above or washed out of underwater coal outcrops, but by the time of Henry VIII, it was understood to derive from the way it was carried to London by sea. In 1257–1259, coal from Newcastle upon Tyne was shipped to London for the smiths and lime-burners building Westminster Abbey. Seacoal Lane and Newcastle Lane, where coal was unloaded at wharves along the River Fleet, still exist.
These easily accessible sources had largely become exhausted (or could not meet the growing demand) by the 13th century, when underground extraction by shaft mining or adits was developed. The alternative name was "pitcoal", because it came from mines. The development of the Industrial Revolution led to the large-scale use of coal, as the steam engine took over from the water wheel. In 1700, five-sixths of the world's coal was mined in Britain. Britain would have run out of suitable sites for watermills by the 1830s if coal had not been available as a source of energy. In 1947 there were some 750,000 miners in Britain but the last deep coal mine in the UK closed in 2015.
A grade between bituminous coal and anthracite was once known as "steam coal" as it was widely used as a fuel for steam locomotives. In this specialized use, it is sometimes known as "sea coal" in the United States. Small "steam coal", also called dry small steam nuts (or DSSN), was used as a fuel for domestic water heating.
Coal continues to arrive on beaches around the world from both natural erosion of exposed coal seams and windswept spills from cargo ships. Many homes in such areas gather this coal as a significant, and sometimes primary, source of home heating fuel. Scavenging sea-bourne coal for heating is still commonplace on both the Pacific and Atlantic coasts of the U.S.[failed verification]
Emission intensity is the per unit of electricity generated. Of the currently widely used methods of generating electricity the emission intensity of coal and oil is high, as they emit around 1000g of CO2eq for each kWh generated; natural gas and pumped hydro are medium emission intensity at around 500g CO2eq per kWh; and all other methods are typically low emission intensity of under 100g per kWh. The emission intensity of coal varies with type and generator technology and exceeds 1200g per kWh in some countries.
The energy density of coal, that is its heating value, is roughly 24 megajoules per kilogram (approximately 6.7 kilowatt-hours per kg). For a coal power plant with a 40% efficiency, it takes an estimated 325 kg (717 lb) of coal to power a 100 W lightbulb for one year.
27.6% of world energy was supplied by coal in 2017 and Asia used almost three quarters of it.
The composition of coal is reported either as a proximate analysis (moisture, volatile matter, fixed carbon, and ash) or an ultimate analysis (ash, carbon, hydrogen, nitrogen, oxygen, and sulfur). The "volatile matter" does not exist by itself (except for some adsorbed methane) but designates the volatile compounds that are produced and driven off by heating the coal. A typical bituminous coal may have an ultimate analysis on a dry, ash-free basis of 84.4% carbon, 5.4% hydrogen, 6.7% oxygen, 1.7% nitrogen, and 1.8% sulfur, on a weight basis.
Coke is a solid carbonaceous residue derived from coking coal (a low-ash, low-sulfur bituminous coal, also known as metallurgical coal), which is used in manufacturing steel and other iron products. Coke is made from coking coal by baking in an oven without oxygen at temperatures as high as 1,000 °C, driving off the volatile constituents and fusing together the fixed carbon and residual ash. Metallurgical coke is used as a fuel and as a reducing agent in smelting iron ore in a blast furnace. The carbon monoxide produced by its combustion reduces hematite (an iron oxide) to iron.
Coking coal should be low in ash, sulfur, and phosphorus, so that these do not migrate to the metal. The coke must be strong enough to resist the weight of overburden in the blast furnace, which is why coking coal is so important in making steel using the conventional route. Coke from coal is grey, hard, and porous and has a heating value of 29.6 MJ/kg. Some cokemaking processes produce byproducts, including coal tar, ammonia, light oils, and coal gas.
Finely ground bituminous coal, known in this application as sea coal, is a constituent of foundry sand. While the molten metal is in the mould, the coal burns slowly, releasing reducing gases at pressure, and so preventing the metal from penetrating the pores of the sand. It is also contained in 'mould wash', a paste or liquid with the same function applied to the mould before casting. Sea coal can be mixed with the clay lining (the "bod") used for the bottom of a cupola furnace. When heated, the coal decomposes and the bod becomes slightly friable, easing the process of breaking open holes for tapping the molten metal.
Scrap steel can be recycled in an electric arc furnace; and an alternative to making iron by smelting is direct reduced iron, where any carbonaceous fuel can be used to make sponge or pelletised iron. To lessen carbon dioxide emissions hydrogen can be used as the reducing agent and biomass or waste as the source of carbon.
Coal gasification, as part of an integrated gasification combined cycle (IGCC) coal-fired power station, is used to produce syngas, a mixture of carbon monoxide (CO) and the hydrogen (H2) gas to fire gas turbines to produce electricity. Syngas can also be converted into transportation fuels, such as gasoline and diesel, through the Fischer-Tropsch process; alternatively, syngas can be converted into methanol, which can be blended into fuel directly or converted to gasoline via the methanol to gasoline process. Gasification combined with Fischer-Tropsch technology is used by the Sasol chemical company of South Africa to make motor vehicle fuels from coal and natural gas.
During gasification, the coal is mixed with oxygen and steam while also being heated and pressurized. During the reaction, oxygen and water molecules oxidize the coal into carbon monoxide (CO), while also releasing hydrogen gas (H2). This used to be done in underground coal mines, and also to make town gas which was piped to customers to burn for illumination, heating, and cooking.
If the refiner wants to produce gasoline, the syngas is routed into a Fischer-Tropsch reaction. This is known as indirect coal liquefaction. If hydrogen is the desired end-product, however, the syngas is fed into the water gas shift reaction, where more hydrogen is liberated:
Coal can be converted directly into synthetic fuels equivalent to gasoline or diesel by hydrogenation or carbonization. Coal liquefaction emits more carbon dioxide than liquid fuel production from crude oil. Mixing in biomass and using CCS would emit slightly less than the oil process but at a high cost. State owned China Energy Investment runs a coal liquefaction plant and plans to build 2 more.
Coal liquefaction may also refer to the cargo hazard when shipping coal.
Chemicals have been produced from coal since the 1950s. Coal can be used as a feedstock in the production of a wide range of chemical fertilizers and other chemical products. The main route to these products is coal gasification to produce syngas. Primary chemicals that are produced directly from the syngas include methanol, hydrogen and carbon monoxide, which are the chemical building blocks from which a whole spectrum of derivative chemicals are manufactured, including olefins, acetic acid, formaldehyde, ammonia, urea and others. The versatility of syngas as a precursor to primary chemicals and high-value derivative products provides the option of using relatively inexpensive coal to produce a wide range of valuable commodities.
Because the slate of chemical products that can be made via coal gasification can in general also use feedstocks derived from natural gas and petroleum, the chemical industry tends to use whatever feedstocks are most cost-effective. Therefore, interest in using coal tends to increase for higher oil and natural gas prices and during periods of high global economic growth that may strain oil and gas production. Also, production of chemicals from coal is of much higher interest in countries like South Africa, China and India where there are abundant coal resources. The abundance of coal combined with lack of natural gas resources in China is a strong inducement for the coal to chemicals industry there. Similarly, Sasol has built and operated coal-to-chemicals facilities in South Africa.
Coal to chemical processes require substantial quantities of water. Much coal to chemical production is in China where coal dependent provinces such as Shanxi are struggling to control its pollution.
Refined coal is the product of a coal-upgrading technology that removes moisture and certain pollutants from lower-rank coals such as sub-bituminous and lignite (brown) coals. It is one form of several precombustion treatments and processes for coal that alter coal's characteristics before it is burned. Thermal efficiency improvements are achievable by improved pre-drying (especially relevant with high-moisture fuel such as lignite or biomass). The goals of precombustion coal technologies are to increase efficiency and reduce emissions when the coal is burned. Precombustion technology can sometimes be used as a supplement to postcombustion technologies to control emissions from coal-fueled boilers.
Coal burnt as a solid fuel in coal power stations to generate electricity is called thermal coal. Coal is also used to produce very high temperatures through combustion. Efforts around the world to reduce the use of coal have led some regions to switch to natural gas and electricity from lower carbon sources.
When coal is used for electricity generation, it is usually pulverized and then burned in a furnace with a boiler. The furnace heat converts boiler water to steam, which is then used to spin turbines which turn generators and create electricity. The thermodynamic efficiency of this process varies between about 25% and 50% depending on the pre-combustion treatment, turbine technology (e.g. supercritical steam generator) and the age of the plant.
A few integrated gasification combined cycle (IGCC) power plants have been built, which burn coal more efficiently. Instead of pulverizing the coal and burning it directly as fuel in the steam-generating boiler, the coal is gasified to create syngas, which is burned in a gas turbine to produce electricity (just like natural gas is burned in a turbine). Hot exhaust gases from the turbine are used to raise steam in a heat recovery steam generator which powers a supplemental steam turbine. The overall plant efficiency when used to provide combined heat and power can reach as much as 94%. IGCC power plants emit less local pollution than conventional pulverized coal-fueled plants; however the technology for carbon capture and storage after gasification and before burning has so far proved to be too expensive to use with coal. Other ways to use coal are as coal-water slurry fuel (CWS), which was developed in the Soviet Union, or in an MHD topping cycle. However these are not widely used due to lack of profit.
In 2017 38% of the world's electricity came from coal, the same percentage as 30 years previously. In 2018 global installed capacity was 2TW (of which 1TW is in China) which was 30% of total electricity generation capacity. The most dependent major country is South Africa, with over 80% of its electricity generated by coal.
The total known deposits recoverable by current technologies, including highly polluting, low-energy content types of coal (i.e., lignite, bituminous), is sufficient for many years. On the other hand, much may have to be left in the ground to avoid climate change, so maximum use could be reached sometime in the 2020s.
About 8000 Mt of coal are produced annually, about 90% of which is hard coal and 10% lignite. As of 2018 just over half is from underground mines. More accidents occur during underground mining than surface mining. Not all countries publish mining accident statistics so worldwide figures are uncertain, but it is thought that most deaths occur in coal mining accidents in China: in 2017 there were 375 coal mining related deaths in China. Most coal mined is thermal coal (also called steam coal as it is used to make steam to generate electricity) but metallurgical coal (also called "metcoal" or "coking coal" as it is used to make coke to make iron) accounts for 10% to 15% of global coal use.
A court in Australia has cited climate change in ruling against a new coal mine.
China mines almost half the world's coal, followed by India with about a tenth. Australia accounts for about a third of world coal exports, followed by Indonesia and Russia; while the largest importers are Japan and India.
The price of metallurgical coal is volatile and much higher than the price of thermal coal because metallurgical coal must be lower in sulfur and requires more cleaning. Coal futures contracts provide coal producers and the electric power industry an important tool for hedging and risk management.
In some countries new onshore wind or solar generation already costs less than coal power from existing plants (see Cost of electricity by source). However, for China this is forecast for the early 2020s and for south-east Asia not until the late 2020s. In India building new plants is uneconomic and, despite being subsidized, existing plants are losing market share to renewables.
Of the countries which produce coal China mines by far the most, almost half the world's coal, followed by less than 10% by India. China is also by far the largest consumer. Therefore, market trends depend on Chinese energy policy. Although the effort to reduce pollution means that the global long term trend is to burn less coal, the short and medium term trends may differ, in part due to Chinese financing of new coal-fired power plants in other countries.
Countries with annual production higher than 300 million tonnes are shown.
Countries with annual consumption higher than 500 million tonnes are shown. Shares are based on data expressed in tonnes oil equivalent.
Exporters are at risk of a reduction in import demand from India and China.
Coal smokestack emissions cause asthma, strokes, reduced intelligence, artery blockages, heart attacks, congestive heart failure, cardiac arrhythmias, mercury poisoning, arterial occlusion, and lung cancer.
Annual health costs in Europe from use of coal to generate electricity are estimated at up to €43 billion.
In China, improvements to air quality and human health would increase with more stringent climate policies, mainly because the country's energy is so heavily reliant on coal. And there would be a net economic benefit.
A 2017 study in the Economic Journal found that for Britain during the period 1851–1860, "a one standard deviation increase in coal use raised infant mortality by 6–8% and that industrial coal use explains roughly one-third of the urban mortality penalty observed during this period."
Breathing in coal dust causes coalworker's pneumoconiosis which is known colloquially as "black lung", so-called because the coal dust literally turns the lungs black from their usual pink color. In the United States alone, it is estimated that 1,500 former employees of the coal industry die every year from the effects of breathing in coal mine dust.
Huge amounts of coal ash and other waste is produced annually. Use of coal generates hundreds of millions of tons of ash and other waste products every year. These include fly ash, bottom ash, and flue-gas desulfurization sludge, that contain mercury, uranium, thorium, arsenic, and other heavy metals, along with non-metals such as selenium.
Around 10% of coal is ash: coal ash is hazardous and toxic to human beings and some other living things. Coal ash contains the radioactive elements uranium and thorium. Coal ash and other solid combustion byproducts are stored locally and escape in various ways that expose those living near coal plants to radiation and environmental toxics.
Water systems are affected by coal mining. For example, mining affects groundwater and water table levels and acidity. Spills of fly ash, such as the Kingston Fossil Plant coal fly ash slurry spill, can also contaminate land and waterways, and destroy homes. Power stations that burn coal also consume large quantities of water. This can affect the flows of rivers, and has consequential impacts on other land uses. In areas of water scarcity, such as the Thar Desert in Pakistan, coal mining and coal power plants would use significant quantities of water.
One of the earliest known impacts of coal on the water cycle was acid rain. Approximately 75 Tg/S per year of sulfur dioxide (SO2) is released from burning coal. After release, the sulfur dioxide is oxidized to gaseous H2SO2 which scatters solar radiation, hence its increase in the atmosphere exerts a cooling effect on climate. This beneficially masks some of the warming caused by increased greenhouse gases. However, the sulfur is precipitated out of the atmosphere as acid rain in a matter of weeks, whereas carbon dioxide remains in the atmosphere for hundreds of years. Release of SO2 also contributes to the widespread acidification of ecosystems.
Disused coal mines can also cause issues. Subsidence can occur above tunnels, causing damage to infrastructure or cropland. Coal mining can also cause long lasting fires, and it has been estimated that thousands of coal seam fires are burning at any given time. For example, Brennender Berg has been burning since 1668 and is still burning in the 21st century.
The production of coke from coal produces ammonia, coal tar, and gaseous compounds as by-products which if discharged to land, air or waterways can pollute the environment. The Whyalla steelworks is one example of a coke producing facility where liquid ammonia is discharged to the marine environment.
Thousands of coal fires are burning around the world. Those burning underground can be difficult to locate and many cannot be extinguished. Fires can cause the ground above to subside, their combustion gases are dangerous to life, and breaking out to the surface can initiate surface wildfires. Coal seams can be set on fire by spontaneous combustion or contact with a mine fire or surface fire. Lightning strikes are an important source of ignition. The coal continues to burn slowly back into the seam until oxygen (air) can no longer reach the flame front. A grass fire in a coal area can set dozens of coal seams on fire. Coal fires in China burn an estimated 120 million tons of coal a year, emitting 360 million metric tons of CO2, amounting to 2–3% of the annual worldwide production of CO2 from fossil fuels. In Centralia, Pennsylvania (a borough located in the Coal Region of the United States), an exposed vein of anthracite ignited in 1962 due to a trash fire in the borough landfill, located in an abandoned anthracite strip mine pit. Attempts to extinguish the fire were unsuccessful, and it continues to burn underground to this day. The Australian Burning Mountain was originally believed to be a volcano, but the smoke and ash come from a coal fire that has been burning for some 6,000 years.
The reddish siltstone rock that caps many ridges and buttes in the Powder River Basin in Wyoming and in western North Dakota is called porcelanite, which resembles the coal burning waste "clinker" or volcanic "scoria". Clinker is rock that has been fused by the natural burning of coal. In the Powder River Basin approximately 27 to 54 billion tons of coal burned within the past three million years. Wild coal fires in the area were reported by the Lewis and Clark Expedition as well as explorers and settlers in the area.
The largest and most long term effect of coal use is the release of carbon dioxide, a greenhouse gas that causes climate change and global warming. Coal-fired power plants were the single largest contributor to the growth in global CO2 emissions in 2018, 40% of the total fossil fuel emissions. Coal mining can emit methane, another greenhouse gas.
In 2016 world gross carbon dioxide emissions from coal usage were 14.5 giga tonnes. For every megawatt-hour generated, coal-fired electric power generation emits around a tonne of carbon dioxide, which is double the approximately 500 kg of carbon dioxide released by a natural gas-fired electric plant. In 2013, the head of the UN climate agency advised that most of the world's coal reserves should be left in the ground to avoid catastrophic global warming. To keep global warming below 1.5°C or 2°C hundreds, or possibly thousands, of coal-fired power plants will need to be retired early.
"Clean" coal technology usually addresses atmospheric problems resulting from burning coal. Historically, the primary focus was on SO2 and NOx, the most important gases which caused acid rain; and particulates which cause visible air pollution, illness and premature deaths. SO2 can be removed by flue-gas desulfurization and NO2 by selective catalytic reduction (SCR). Particulates can be removed with electrostatic precipitators. Although perhaps less efficient wet scrubbers can remove both gases and particulates. And mercury emissions can be reduced up to 95%. However capturing carbon dioxide emissions is generally not economically viable.
Satellite monitoring is now used to crosscheck national data, for example Sentinel-5 Precursor has shown that Chinese control of SO2 has only been partially successful. It has also revealed that low use of technology such as SCR has resulted in high NO2 emissions in South Africa and India.
A few Integrated gasification combined cycle (IGCC) coal-fired power plants have been built with coal gasification. Although they burn coal more efficiently and therefore emit less pollution, the technology has not generally proved economically viable for coal, except possibly in Japan although this is controversial.
Although still being intensively researched and considered economically viable for some uses other than with coal; carbon capture and storage has been tested at the Petra Nova and Boundary Dam coal-fired power plants and has been found to be technically feasible but not economically viable for use with coal, due to reductions in the cost of solar PV technology.
In 2018 USD 80 billion was invested in coal supply but almost all for sustaining production levels rather than opening new mines. In the long term coal and oil could cost the world trillions of dollars per year. Coal alone may cost Australia billions, whereas costs to some smaller companies or cities could be on the scale of millions of dollars. The economies most damaged by coal (via climate change) may be India and the US as they are the countries with the highest social cost of carbon. Bank loans to finance coal are a risk to the Indian economy.
China is the largest producer of coal in the world. It is the world's largest energy consumer, and coal in China supplies 60% of its primary energy. However two fifths of China's coal power stations are estimated to be loss-making.
Air pollution from coal storage and handling costs the USA almost 200 dollars for every extra ton stored, due to PM2.5. Coal pollution costs the EU €43 billion each year. Measures to cut air pollution benefit individuals financially and the economies of countries such as China.
Broadly defined total subsidies for coal in 2015 have been estimated at around US$2.5 trillion, about 3% of global GDP. As of 2019 G20 countries provide at least US$63.9 billion of government support per year for the production of coal, including coal-fired power: many subsidies are impossible to quantify but they include US$27.6 billion in domestic and international public finance, US$15.4 billion in fiscal support, and US$20.9 billion in state-owned enterprise (SOE) investments per year. In the EU state aid to new coal-fired plants is banned from 2020, and to existing coal-fired plants from 2025. However government funding for new coal power plants is being supplied via Exim Bank of China, the Japan Bank for International Cooperation and Indian public sector banks. Coal in Kazakhstan was the main recipient of coal consumption subsidies totalling US$2 billion in 2017. Coal in Turkey benefited from substantial subsidies.
Some coal-fired power stations could become stranded assets, for example China Energy Investment, the world's largest power company, risks losing half its capital. However state owned electricity utilities such as Eskom in South Africa, Perusahaan Listrik Negara in Indonesia, Sarawak Energy in Malaysia, Taipower in Taiwan, EGAT in Thailand, Vietnam Electricity and EÜAŞ in Turkey are building or planning new plants. As of 2019 this may be helping to cause a carbon bubble which could cause financial instability if it bursts.
Countries building or financing new coal-fired power stations, such as China, India, and Japan, face mounting international criticism for obstructing the aims of the Paris Agreement. In 2019, the Pacific Island nations (in particular Vanuatu and Fiji) criticized Australia for failing to cut their emissions at a faster rate than they were, citing concerns about coastal inundation and erosion.
Opposition to coal pollution was one of the main reasons the modern environmental movement started in the 19th century.
In order to meet global climate goals and provide power to those that don't currently have it coal power must be reduced from nearly 10,000 TWh to less than 2,000 TWh by 2040. Many countries, such as the Powering Past Coal Alliance, have already or are transitioned away from coal; the largest transition announced so far being Germany, which is due to shut down its last coal-fired power station between 2035 and 2038. Some countries use the ideas of a "just transition", for example to use some of the benefits of transition to provide early pensions for coal miners. However low-lying Pacific Islands are concerned the transition is not fast enough and that they will be inundated by sea level rise; so they have called for OECD countries to completely phase out coal by 2030 and other countries by 2040.
Although many countries have coal underground not all will be consumed.
Of the three fossil fuels, coal has the most widely distributed resources. Coal is mined on all continents except Antarctica. However many such resources have no economic value (much value has been destroyed by shale gas fracking). The largest resources are found in the United States, Russia, China, Australia and India.
Nowadays "peak coal" means the point in time when consumption of coal reaches a maximum. Although coal use peaked in 2018 the drop in 2019 was only about 1% but is likely to continue to fall.
Coal-fired generation puts out about twice the amount of carbon dioxide—around a tonne for every megawatt hour generated—than electricity generated by burning natural gas at 500 kg of greenhouse gas per megawatt hour. In addition to generating electricity, natural gas is also popular in some countries for heating and as an automotive fuel.
The use of coal in the United Kingdom declined as a result of the development of North Sea oil and the subsequent dash for gas during the 1990s. In Canada some coal power plants, such as the Hearn Generating Station, switched from coal to natural gas. In 2017, coal power in the United States provided 30% of the electricity, down from approximately 49% in 2008, due to plentiful supplies of low cost natural gas obtained by hydraulic fracturing of tight shale formations.
Some coal miners are concerned their jobs may be lost in the transition.
It is also customary and considered lucky in Scotland and the North of England to give coal as a gift on New Year's Day. This occurs as part of First-Footing and represents warmth for the year to come.